Acest magazin utilizeaza cookie-uri pentru a va imbunatati experienta pe site-ul nostru.               Apasati aici pt a inchide ->

close

Categorii

Producători

Z-Uno - Z-Wave Board for Arduino Afisare la marime maxima

Z-Uno - Z-Wave Board for Arduino

Z-Uno is a fully DIY product. It is made for those who are limited by existing choice of Z-Wave products and wants to extend their smart homes with more sensors and actuators: connect LEDs, buttons, switches, motors or any low voltage sensor including most of Arduino compatible sensors.

Mai multe detalii

ZMEEZUNO

Disponibilitate: Livrare dupa 1 mai

263,06 lei cu TVA

» Add to my wishlist

Producator
Z-wave.me

Z-Uno is the first and only easy to use developer board that allows you to create your own Z-Wave device without deep knowledge of Z-Wave protocol or programming. Z-Uno is a mix of Z-Wave home automation radio protocol power and Arduino simplicity. Being inspired by Arduino project Z-Uno inherits all concepts of easy-to-use hardware and software solutions, keeping maximum flexibility.

Z-Uno is a fully DIY product. It is made for those who are limited by existing choice of Z-Wave products and wants to extend their smart homes with more sensors and actuators: connect LEDs, buttons, switches, motors or any low voltage sensor including most of Arduino compatible sensors.

Z-Uno programming is done by writing sketch in simplified C language and loaded into Z-Uno using Arduino IDE. Many examples and comprehensive tutorials will help you to make your own project.

Being Z-Wave Plus certified device, Z-Uno is the perfect companion for you RaZberry gateway. Z-Uno is compatible with other controllers too: among them Fibaro Home Center 2/Lite, Vera Edge and Zipato Zipabox.

Unveil your imagination to create:

  • battery powered in-wall remote switch
  • rotary dimmer control
  • temperature/soil humidity/luminosity/voltage/distance or any other sensors as well as dry contact sensor or tick counter
  • low voltage switch
  • IR blaster
  • LED driver
  • motor driver
  • battery powered keypad
  • converter from any protocol to Z-Wave (using SPI/UART/I2C/1-wire bus)
  • ... or any other device you dreamed about

 

Make your own z-wave device:

  • control any Arduino compatible peripherals
  • define your own logic by modifying your sketch
  • use Arduino IDE and language to write and upload sketches
  • easy to use
  • requires no knowledge of Z-Wave protocol
  • complete DIY solution

Hardware specification:

  • 28 kB Flash memory for your sketches
  • 2 kB RAM available
  • Z-Wave RF transmitter at 9.6/40/100 kbps
  • 26 GPIO (overlaps with special hardware controllers)
  • 4 ADC
  • 5 PWM
  • 2 UART
  • 1 USB (serial port)
  • 64 kB EEPROM
  • 1 SPI (master or slave)
  • 4 IR controllers, 1 IR learn capability
  • 1 TRIAC/ZEROX to control dimmer
  • 1 Interrupt
  • 2 Timers 16 MHz or external source
  • I2C (software)
  • 1-wire (software)
  • 8x6 Keypad Scanner
  • 2 service LED, 1 service button
  • 1 user test LED

Power modes:

  • USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • always on, sleeping or FLiRS (Frequently Listening)

Z-Wave supported features:

  • Z-Wave Plus compliant
  • all Z-Wave frequencies (check availability)
  • out of the box support of AES 128 bit Security
  • upgrade via USB or radio (Z-Wave OTA)
  • Multichannel (10 channels)
  • 5 Association groups
  • controls switches, dimmers, door locks and scenes
  • works with gateways and/or directly with other Z-Wave devices

Channel types:

  • Binary Switch
  • Multilevel Switch
  • Color Switch
  • Binary Sensor
  • Multilevel Sensor
  • Meter

Dimensions:

  • L×W×H: 39×20×16 mm (PCB dimentions with all compinents)
  • L×W×H: 39×20×7 mm (PCB dimentions with PLS and battery connectors removed)
  • Antenna lenght: 86 mm (89 mm with isolation), can be bent to better fit your dimensions
  • Wigth: 7 g

Antenna:

  • Antenna type: wire antenna 86 mm for 865-870 MhZ
  • Alternative antenna: optional u.fl connector can be soldered (to RF2 pads)

Electrical characteristics:

  • Digital pin in logical 1: > 2.1 V, leakage current 10 μA
  • Digital pin in logical 0: < 0.9 V, leakage current 10 μA or 40-120 μA (with internal pull-up enabled)
  • Internal pullup resistor: 15-20 kΩ (at +25°C)
  • Digital pin out logical 1: > 2.4 V, max current sourcing 8 mA (16 mA for digital pins 3-6)
  • Digital pin out logical 0: < 0.4 V, max current sinking 8 mA (16 mA for digital pins 3-6)
  • Total max current sourcing from GPIO pins: 120 mA
  • Power consumption on 3.3 V: in always listening mode 50 mA, in sleep mode 1 mA (about 7 μA if one DC-DC is unsoldered), in FLiRS mode 1 mA (about 70 μA if one DC-DC is unsoldered)

 — these features will be implemented in near future

Deeper insight

Know more about Z-Uno internals.

Pinout


Contactati-ne

Suntem disponibil 24/7

Telefon:+4 0772 00 22 70

Contactati-ne

Newsletter